We carry replacement parts, repair parts and accessories for 9 Husqvarna Tiller models REFINE BY: Model (160 parts) Rear tine tiller, Gas TILLER Shop Parts Model (92 parts) Front tine tiller, Gas TILLER Shop Parts Model (94 parts) Front tine tiller, Gas FRONT TINE TILLER Shop Parts Model (163 parts) Rear tine tiller, Gas TILLER Shop Parts Model (93 parts) Front tine tiller, Gas TILLER Shop Parts Model FT900 ( ) (93 parts) Front tine tiller, Gas TILLER Shop Parts Model (97 parts) Front tine tiller, Gas TILLER Shop Parts Model (163 parts) Rear tine tiller, Gas TILLER Shop Parts Model 500 RTTA (163 parts) Rear tine tiller, Gas TILLER Shop Parts If you love gardening, you know how much your Husqvarna tiller can help you prepare soil for planting and even help with the weeding. Sometimes, however, the wheels or tines on a tiller can stop turning properly. Here are some simple troubleshooting tips to help you figure out where the problem lies. Adjust the Clutch Cable If the clutch cable on your Husqvarna tiller is badly adjusted, the drive system isn't going to engage and disengage properly, resulting in the wheels refusing to turn. Check out your clutch cable as part of your tiller troubleshooting. Make the needed adjustments, and if it looks damaged or broken, replace the cable. Check the Tiller Drive Belt If the tiller drive belt is worn, it slips and consequently fails to drive the tiller's wheels and tines as it should. Check your tiller drive belt for wear. If it's broken or appears worn, replace it. Tiller repair parts such as drive belts are readily available at Sears Parts Direct. Replace the Tiller Tine Shaft Clevis Pin The tiller tine shaft clevis pin is a small part that helps protect your tiller's engine. If the tines hit a fixed object while working, the tine shaft clevis pin.
Page 1 Repair Parts Manual IPL Manual DRT900 E/ Please read the operator's manual carefully and make sure you understand the instructions before using the machine. Lisez très attentivement et soyez certain de comprende ces English instructions avant d’utiliser cette machine. Page 2: Repair Parts REPAIR PARTS TILLER - - MODEL NUMBER DRT900 E ( PRODUCT NUMBER HANDLE ASSEMBLY 12 13 handle_assy_106 PART PART DESCRIPTION DESCRIPTION Nut, Hex Flange unc Control, Throttle Grip, Handle Bolt, Pivot Console, Control Screw. Page 3 REPAIR PARTS TILLER - - MODEL NUMBER DRT900 E ( PRODUCT NUMBER MAINFRAME, LEFT SIDE PART PART DESCRIPTION DESCRIPTION Nut, Hex Belt, V Shield, Inner Belt Guard RT Pulley, Idler Pin Spirol Flared Ring, Klip. Page 4 REPAIR PARTS TILLER - - MODEL NUMBER DRT900 E ( PRODUCT NUMBER MAINFRAME, RIGHT SIDE PART PART DESCRIPTION DESCRIPTION Locknut, Hex, Flange – – – – – – Engine, Briggs & Stratton Bracket, Reinforcement R. H. Model No. Page 5 REPAIR PARTS TILLER - - MODEL NUMBER DRT900 E ( PRODUCT NUMBER TRANSMISSION 13 15 transmission_25 PART PART DESCRIPTION DESCRIPTION Trans mis sion Assembly ( In cludes Shaft, Re duc tion (2nd) Key Nos. 2-52) Screw, Whiz, Lock x Gearcase, L. H. Page 6 REPAIR PARTS TILLER - - MODEL NUMBER DRT900 E ( PRODUCT NUMBER TINE SHIELD tine_shield_23_in_r1 PART PART DESCRIPTION DESCRIPTION Nut, Lock Hex Flange unc Hinge Shield, Side, Outer L. H. Bolt, Carriage.
. Belt guard Eng 2. Screw 3. Screw 4. Hairpin clip and retaining pin 5. Hex nut (located behind tire) 6. New tine 7. Worn tine 8. Sharp edge 9. Hairpin clip 10. Retaining pin Figure 18 Figure 19 Figure 20 Tine Tine max. Ground drive belt replacement a. Remove hairpin clip and retaining pin (fig. 18) from hub of left hand wheel. Pull wheel out from tiller about inches. b. Remove belt guard by removing two (2) screws, one (1) hex nut and three (3) washers so that belt guard can slide straight out away from engine (fig. 18). c. Loosen belt guide (fig. 17-inset) d. Remove old belt by slipping from idler pulley (fig. 17) first. e. Place new belt in groove to transmission pulley (large pulley) and into groove of engine pulley (fig. 17). Belt must be in groove on top of idler pulley (fig. 17). Note positon of belt to guides. Tighten belt guide (fig. 17 -inset) Tine replacement A badly worn tine causes your tiller to work harder and dig shallower. Most important, worn tines can not chop and shred organic matter as effectively nor bury it as deeply as good tines. A tine this worn (fig. 19) needs to be replaced. To maintain the superb tilling performance fo this machine the tines should be checked for sharpness, bending, particulary the tines which are next to the transmis- sion (fig. 20). If the gap between the tines exceeds inches, they should be replaced or straightened as neces- sary. New tines should be assembled as shown in figure 21. Sharpened tine edges will rotate rearward from above (fig. 21). CAUTION! Never tamper with the engine governor, which is factory set for proper engine speed. Figure 21 wear and Counter tine rotation 1. Riemenabdeckung 2. Schrauben 3. Schrauben 4. Haarnadelklemme und Sicherungsstift 5. Sechskantmutter (hinter dem Seil) 6. Neue Zinke 7. Verschlissene Zinke 8. Geschärfte Schneide 9. Haarnadelklemme 10.
Download Now